Any prominent appliance in your home, including your water softener, can work or stop at any time.
However, if you are experiencing some problem with your system, here is a water softener troubleshooting guide to help you identify the problem and fix it yourself or call a client.
Popular Kinetico Water Softener Problems & How To Solve It
Kinetico is one of the most popular and widespread water softener brands.
These devices are known for their quality and minimal problems, but they can repeatedly stop working correctly.
Furthermore, these are some of the most common problems that can occur.
- Stuck Regeneration
- Resin Replacement
- Kinetico Water Softener Adjustments
Stuck Regeneration
To solve this problem, first, check the switch, make sure it is working properly, and then do it with the control header and timer.
Next, make sure all are programmed and executed correctly.
In case of improper programming, it is better to reset your water softener.
And especially, program the regeneration cycle. Next, inspect the system for blocked debris and clean it.
Trapped debris in the system is a common cause of recurrence, but the problem is simple to fix.
Suppose there is a low water pressure or a broken switch, you should contact a plumber.
Or the water softener must professionally install.
Resin Replacement
One of the main problems with Kinetico is the damaged resin beds.
One of the main problems with Kinetico is the damaged resin beds.
With Kinetico, replacing the bed is more accessible and less costly as the problem is constantly occurring.
To replace a resin bed, follow these simple steps:
- Measure the resin in the tank to decide how much resin you need.
- Turn the softener valve to avoid the spot and activate the dial to start manual regeneration.
- Remove the main valve and disconnect the plumber using a screwdriver.
- Put the old resin in the softener as well as the old riser tube.
- Cut the new riser tube to the same height as the old one and insert it into the resin tank.
- Fill the resin tank with a new resin, reinstall the valve, and reconnect the water softener to your plumbing.
- Return the valve to its working position and check for leaks.
Kinetico Water Softener Adjustments
Sometimes, a moving water softener does not need to repair, and all you need to do is adjust your equipment correctly to get soft water.
However, as its name implies, the kinetic water softener does not use electricity; It depends on the kinetic energy of the water to act instead, and it has no timer or buttons.
For this reason, maintaining your water softener can be challenging. Therefore, if you want to redesign your software, follow these steps manually:
- Deactivate your softener bypass valve.
- Open the soft water hose to remove the water pressure.
- Using a screwdriver, push the screws into the water softener valve and turn it in the opposite direction until the tab reaches the brine or wash point indicator.
- Replace the bypass valve with the service station.
If you interested in Kinetico brine tank float adjustment this article will guide you
Kinetico brine tank float adjustment (how to do it)
Common Water Softener Problems & How To Fix it
Water softener problems Salt tank water
The primary focus faced by water softener users may be a salt tank filled with water.
Also, it is usually causing by overflow or freezing.
However, the problem can cause by a variety of factors.
By identifying the exact reason for water in the salt tank, you can fix the unit correctly.
The water softener makes the water brown.
We have noticed that brown water is flowing from the tap at least once.
It’s easy to understand that drinking this water is not good, but you may think it could cause a disaster if you have a water softener installed.
For your information, there is a remote opportunity to get brown water because of the softener.
Often the cause of brown water is excessive dirt and sediment in a damaged pipe or water supply.
Also, the accumulation of bacteria in your softener can be the cause of unbearable brown water.
Disinfect your system with chlorine or hydrogen peroxide to eliminate this possibility.
Sterilize two cups into the brine tank, run two or three regenerative cycles, and then drain your pump.
If the issue persists, call a plumber to have your system checked for water leaks or contact your water supplier to see if any faults have been reported.
Water softener problems Salt bridges
Water softeners are designing to prevent mineral salts in your pipes and fittings.
But amusingly, they are subject to salt – it is still a mineral – scaling up in the tank and the system lines.
This buildup can sometimes form salt bridges at the bottom of the tank, preventing your system from softening the water.
The effortless method to define a salt bridge is with a brine salt crust that stops water from flowing through the brine tank.
And also prevents the entire system from running its regeneration cycles.
Unfortunately, an unidentified salt bridge can eventually break the system.
Once identified, however, salt bridges are more accessible to repair by removing the salt crust.
Also, be sure to clean any salt around the edges of the tank.
Water Softener Problems Resin Beads
Salt-based water softeners use resin beads to increase their effectiveness.
Specially, these beads usually last as long as the system exists.
However, in some cases, their potential may be broken or lost, and you may need to refill the salt frequently.
Another indicator that gum beads do not work correctly in the presence of floating particles in softened water.
Further, it can be troublesome, but the solution is quite simple.
Clean or replace gum beads according to the instructions in your user manual.
This problem is usually easy to solve on your own without spending a fortune.
Water softener issues Salty taste.
Drinking salty water can be an unpleasant experience, especially if you have to deal with stomach upset.
Although most all the water softeners use salt to reduce the hardness of the liquid, the taste of the water should not be salty.
If so, it’s a sign that something is wrong with your system.
Often, you use too much salt.
The drain pipe may also become clogged, at which point brine may not be pump out during the regeneration cycle.
The water softener does not regenerate
The correct performance of your system depends on how well you maintain the device.
For example, water softeners need to activate their regeneration cycles to work properly but may fail to do this for several reasons.
The most common is a faulty regeneration timeline.
Without the timer, the machine would never know that its cycle should activate.
To check if this is a problem, set the regeneration timer daily and check if you can hear the system regenerate on time.
If you do not hear the specific sounds, the timer is broken, and you will have to replace it.
Also, freezing and buildup of contaminants will prevent the system from regenerating.
At this point, you will hear a definite cyclical sound, but you will notice that the soft water is salty.
If this happens, check the pipes and ensure the water is allowed to flow to ensure proper functioning.
The water softener continues to function.
There are several causes why your water softener may not work again.
The most common reason is the inability to draw brine from the tank.
It is most often causing by sediment buildup in salt bridges or waterways.
Low water pressure can be another reason your system gets stuck in regenerative mode.
Also, check the settings and switches.
Incorrect settings or a broken switch can cause an endless regeneration cycle or cause cycle prolongation errors.
The water softener sounds funny.
One thing you need to know from the beginning is that water softeners should not be loud.
Sometimes you will hear it during the regeneration cycle, but it should still be relatively quiet, and the sound should be as smooth as a running engine.
And also, if the system makes funny noises or it’s unbelievably loud, it’s a sign of something wrong.
Noise may be occurred due to clogged valves or water lines, broken air valves, and worn-out timers.
The water softener is leaking.
Another common water softener problem is not noticing leaks in tanks, lines, or other components.
Leak detection can be tedious, but you should check every part of the system to see where the water is coming from.
Once detected, you will need to install or replace the component.
Fortunately, most leaks are causing by errors in the installation, so they are easy to fix.
However, if you need to repair or replace parts, remember to follow the manufacturer’s instructions to avoid further damage to the system.
Operation Error
Like other systems that rely on manual processing and input, water softeners are prone to operate errors.
If your system is particularly complex and you do not have the technical knowledge to set it up properly, countless things can go wrong.
Before activating the system, make sure that your device can use full confidence and resolve user errors.
If not, ask a professional to install and set up your unit.
Conclusion
As mentioned above, most water softener problems are easy to solve with minimal hassle and effort.
Remember, when in doubt, call a professional to prevent further damage to your device.
Continue Reading…
